Call Us (800) 924-2213 • Mon - Sat 10:30 to 5:30 PST

Gold Vocabulary

Colored Gold

Colors in gold, other than yellow, result from the combination of metal alloys mixed with the yellow gold to create various hues. Depending on the alloy(s) used it is possible to create white, rose, green, blue, grey and other shades of gold.

The different recipes produce different alloys which naturally have different characteristics in terms of ductility, malleability, and hardness. These differing properties make different alloys suitable for different purposes.

Colors of Gold

   
Yellow Gold
Yellow gold is the most popular alloy of gold. Pure gold is very soft and very difficult to work into jewelry. Alloys can be added to yellow gold to enhance the yellow hue and create a harder, more workable alloy. Typical yellow gold alloys are a mixture of gold, silver, copper and sometimes zinc.
White Gold
White gold was invented in the 19th century by alloying gold with palladium. It became commercially available as of 1912 in Pforzheim, Germany and gained popularity in the mid-1920’s as a low-cost substitute for platinum. It is an alloy of gold with copper, zinc, and nickel. In more recent times the nickel in this alloy is often been replaced by a member of the platinum family due to the prevalence of nickel allergies.
Rose Gold
Rose gold is a gold alloy displaying a reddish color. This color comes from high amounts of copper in the alloy. 18K Rose gold usually contains 25% copper and 75% gold (note, these are weight percentages, not volume percentages!).
Green Gold
Green gold is an alloy with silver that is usually 75 percent gold and 25 percent fine silver. Green gold can be made with less silver but it usually includes zinc and copper along with the silver.
Grey Gold
Grey gold is an alloy of gold and iron or gold, silver and iron that is a pale grey color.
Blue Gold
Blue Gold is an alloy of 25% arsenic or iron with gold to create a bluish color. Rarely used in jewelry, but sometimes found in “gold á quatre couleurs.”

Gold à Quatre Couleurs

Gold à quatre couleurs refers to the combination of four distinct shades of gold alloy used in a single jewelry item. The colors are inlaid and soldered together to create a harmonious design. The combination of green, red, white and blue gold was the mixture most commonly utilized for jewelry design. Although the process was discovered earlier, the technique didn’t really gain in popularity until c.1750.

Tricolor Gold

Tricolor gold is the use of three colors of gold in jewelry fabrication. Usually, this is a combination of yellow, white and rose or green gold.

Names for Gold Alloys

   
Coin Gold
Coin gold in the United States was an alloy of 9 parts gold, 1 part copper.
Crown Gold
Crown gold is an English term to describe an 18 karat gold alloy.
Drittel Gold
Drittel gold (from German: drittel = 1/3) is an 8 karat gold alloy.
Fine Gold
Fine gold is another way of saying pure gold.
French Gold
French Gold (or Oreide) is a copper alloy that is made of 80% copper, 15% zinc and 5% tin used to imitate gold.
Hera Gold
Hera gold is a German name for a 10 karat gold alloy.
Jou-Jou Or
Jou-jou or (from French: “toy gold”) is a 6 karat gold alloy.
Bluite
Bluite was the trade name of an 18k white gold alloy marketed by Goldfarb & Friedberg, Inc. of New York. Their claim was that it was the “…nearest color to Platinum yet attained.”
Pistol Gold
Pistol gold is a gold alloyed with 895/1000 parts of gold.
Karat Gold
Karat gold is the designation of fineness in an alloy of gold that is never less than 10 karat. It is expressed as the fineness followed by karat gold or just K. Example 14K.
Plumb Gold
Plumb gold is an alloy that tests to be the same fineness as the marking on the item, within a very small tolerance.
Solid Gold
Solid gold refers to 24 karat gold, or fine/pure gold. In 1967 the Federal Trade Commission approved the use of the term solid gold for items that are not hollow and are made of gold alloys. These articles must have a fineness of at least 10k.

Gold Plate

Items that are gold plated are coated with gold by the processes that produce gold-filled or rolled gold plate.

Gold Plating and Bonding

   
Gold Electroform
A very lightweight item is imbued with a heavy appearance through this technique in which a negative mold is put into a special silver or gold bath. Through the use of electricity the metal builds up on the mold forming the object. Sometimes the metal is deposited on a leaf or other natural item or a wax model and, after covering the model in gold, the model is dissolved.
Gold Electroplate
Electroplating involves coating one metal with another through the use of a chemical bath and electric current. The electric current flows through the chemical solution from an anode (a piece of coating metal) to the item to be coated (cathode). Gold electroplate must be a minimum of 7 millionths of an inch of fine gold. When the coating is less than 24 karat the thickness must be proportionately higher.
Karat Clad
Karat Clad is a registered trade name for heavy gold electroplate of at least 100 microns thick and meeting Federal Trade Commission regulations
Vermeil
Vermeil refers to a heavy plating of karat gold over sterling silver. Historically it was a chemical coloring applied to mercury-gilded objects to produce a red or yellow color.
From the FTC guides:
An industry product may be described or marked as “vermeil” if it consists of a base of sterling silver coated or plated on all significant surfaces with gold, or gold alloy of not less than 10 karat fineness, that is of substantial thickness and a minimum thickness throughout equivalent to two and one half (2 1/2) microns (or approximately 100/1,000,000ths of an inch) of fine gold.
Silver-Topped Gold
Silver-topped gold was an innovation by English jeweler James Cox, c. 1767 – the middle of the Georgian Era – which allowed silver to be backed by gold. Prior to this, gems being set in white metal were set in silver only. If the jewelry was not cleaned constantly, silver tarnish, rubbing directly onto skin, could leave marks or stain fabric. Gold does not oxidize and therefore leaves no discoloration on skin or clothing. Since the use of white metal was desirable for gem mounting, silver remained in use for jewelry with the addition of the gold backing. This process continued to be popular until the late eighteenth century.
Platinum Topped Gold
As the technology was developed to make it possible to use platinum in jewelry, it too was added to the top of yellow gold in the same manner as silver. Since Platinum does not oxidize like silver and is in no danger of discoloring skin or clothing, the gold backing was eventually eliminated and jewelry made purely of platinum took its place.
Gold Leaf
Gold leaf is the result of the ancient art of gold beating whereby an ingot of gold is reduced by a rolling mill to 1/800 of an inch in thickness forming a ribbon of gold. This ribbon is separated into 1-inch lengths, placed on a mold and beaten with a 16-pound hammer. The gold is cut and beaten many times until it is extremely thin. The resulting sheets of gold are used to decorate objects, furniture, walls, paintings, sculpture, etc.
Gold Wash
Gold wash refers to a gilded layer with a thickness of less than 0.2 micron.
Sheet Gold
Sheet gold has been used since ancient history. Most ancient golden jewelry started off as a hammered sheet of gold. These sheets could then be cut into desired shapes or rolled up into hollow tubes. Paper-thin sheets were often decorated with repoussé. Sheet gold could be sawn, hammered and bent into figures.
With the invention of the rolling mill, sheets of gold were much easier to be obtained. Gold could be fed in between two rollers rotating in opposite directions so that a flat, even sheet of gold would be produced.
Gold Filled
A mechanical process of plating gold on another metal. This can be done by brazing, soldering, welding, etc. The plating must be at least 1/20th of the weight of the metal in the entire item.
Rolled Gold Plate
Rolled gold plate is accomplished by mechanically plating or fusing a base metal sheet with a sheet of karat gold, at least 10K fineness. The karat gold covering is less than 1/20th of the total weight. Gold-filled is the term used when there is a heavier coating of gold. During the Victorian Era sheets plated by this metal were then cut or stamped into jewelry items.
Doublé d’or
Doublé d’or is the French term for rolled gold plate. Doublé became a synonym for “plated” or plaqué. A gold alloy, whose thickness and fineness are fixed by law, was rolled onto a base metal. Pocket watch cases were often made using this process.
Walz Gold
Walz gold is a German term for doublé articles.

Gold Smudge

gold smudge is a colored smudge, left by jewelry or another metallic object, on the skin of the wearer. Although precious metals are usually non-reactive, in rare cases they may react with the environment. Usually, these special cases involve chemical reactions between the skin of the wearer and the metal, or the alloy, as is sometimes the case during pregnancy or with people who are allergic to that metal. Cosmetics, detergents, pollution and other such factors can also be culprits in causing “gold smudge”.

Gold Imitations

   
French Gold
French Gold (or Oreide) is a copper alloy that is made of 80% copper, 15% zinc and 5% tin used to imitate gold.
Ransch Gold
Ransch gold is a yellow copper alloy (brass) that was used on stage as costume jewelry.
Siladium
Siladium is a brand name for an alloy used as a substitute for white gold in the class rings produced by the company ArtCarved.